![resetting an iei keypad resetting an iei keypad](https://images.edgeindsupply.com/products/U022043.jpg)
Connect the black wire (V-) to the negative on the Maglock, and then connect them to the negative on the power supply. Connect the gray wire (normally closed) to the positive on the maglock. Connect the red wire (V+) to the blue wire (common), and then connect them to the positive on the power supply. IEI 232e Standalone Installation/Programming Manual 4.2 Wiring the 232e Keypad to a Maglock (FailSafe) Use the following steps to connect the 232e keypad to a Maglock (Fail-Safe): 1. Wiring Figure 4 232e Connector and Wire Harness 4. IEI 232e Standalone Installation/Programming Manual 4. Mounting height can vary depending on requirements. To properly size the mounting and wire access hole, use the installation template on the last page of this manual and on the unit’s container. In addition, it can be flush mounted directly to the wall surface by cutting a hole in the wall. Mounting The keypad is designed to be flush mounted using a standard singlegang electrical box. IEI 232e Standalone Installation/Programming Manual 3. IEI 232e Standalone Installation/Programming Manual Figure 1 Mounting a Sentrol 3012 Tamper Switch Figure 2 Mounting a Sentrol 3025T Tamper Switch Document # 6054004, Rev. In addition, all wires and cables used must be stranded and shielded U.L. This system must be installed in accordance with the National Electrical code (NFPA70), local codes, and the authorities having jurisdiction. This section contains information regarding all the requirements necessary to meet U.L. IEI 232e Standalone Installation/Programming Manual Section 3. Specifications Parameter Range/Description Voltage 10-30 VDC, 12-24 VAC Current and Add 20 mA for each alarm relay Environment Indoor and Outdoor Temperature Tolerance -20 ☏ to 130 ☏ Dimensions 4.5" H x 2.75" W x 0.60" D Main Relay (Form C) Alarm Relays: Alarm Shunt, Propped Door, Forced Door Relays (Form C) Document # 6054004, Rev. IEI 232e Standalone Installation/Programming Manual 2. IEI 232e Standalone Installation/Programming Manual 1. Requirements Specifications Mounting Wiring 5.1 Wire Harness Configuration 5.2 Wiring the 232e Keypad to a Maglock (Fail-Safe) 5.3 Wiring the 232e Keypad to an Electric Strike (Fail-Secure) 5.4 Shunting a Normally Closed Zone 5. Note: After you Factory Reset your Arlo Keypad Sensor Hub, you must re-add it to your Arlo account.IEI 232e StandaloneTM Keypad Installation/ Programming Manual Contents Section 1: Section 2: Section 3: Section 4: Section 5: Section 6: Section 7: Section 8: Section 9: Section 10: Features and Product Description 1.1 Features 1.2 Product Description U.L. Tap Remove Device at the bottom of the screen.To factory reset your Arlo Keypad Sensor Hub using the Arlo Secure App: For more information on this process, visit: How do I setup and install my Arlo Keypad Sensor Hub? Note: After factory resetting the Arlo Keypad Sensor Hub, you must re-add it to your Arlo account. The Keypad LEDs will flash white five times to indicate a factory reset. On the Arlo Keypad Sensor Hub, press and hold the and buttons at the same time for 10 seconds.To pair your Arlo Pro 5S camera with SecureLink, visit: How do I pair my Arlo Pro 5S Camera to my Arlo Keypad Sensor Hub using Arlo SecureLink?.All Pro 5S cameras connected with SecureLink will need to be paired again.
![resetting an iei keypad resetting an iei keypad](https://schematron.org/image/iei-212w-keypad-wiring-diagram-2.jpg)
To factory reset your All-in-One Sensor, visit: How do I factory reset the Arlo All-in-One Sensor?.All paired Arlo All-in-One Sensors must be factory reset and paired again after the Arlo Keypad Sensor Hub is reinstalled.You must follow the in-app setup process to use your Arlo Keypad Sensor Hub after a factory reset.Your Arlo Keypad Sensor Hub is also removed from your Arlo account after a factory reset.WARNING: Factory resetting your Arlo Keypad Sensor Hub returns it to default settings. To factory reset the Arlo Keypad Sensor Hub using the Keypad: Press and hold the 5 button on the keypad for 10 seconds.Enter your PIN on the Keypad and press.Press on the Arlo Keypad Sensor Hub to set the Mode to Standby.To restart your Arlo Keypad Sensor Hub using the Keypad: The Keypad Sensor Hub Mode LEDs will illuminate white and cycle in a pattern while the device resets.
![resetting an iei keypad resetting an iei keypad](https://i.ebayimg.com/images/g/TfcAAOSwthlgLieR/s-l400.jpg)
Tap Restart at the bottom of the screen.On the Security Hub Settings screen, tap on the name of your device to access the Device Info screen.To restart your Arlo Keypad Sensor Hub using the Arlo Secure App: If problems persist you may need to perform a factory reset.
![resetting an iei keypad resetting an iei keypad](https://schematron.org/image/iei-2054100-keypad-wiring-diagram-5.jpg)
If you are having issues with your Arlo Keypad Sensor Hub, first try to restart the device.